- CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
TRADE NAME .... : Color Set EXP 16116
PRODUCT TYPE .. : InkJet ink; water based; nonflammable
EMERGENCY PHONE (CHEMTREC 24 HOUR): 800-424-9300
REASON FOR MSDS ISSUE: Formula modification
MSDS VERSION: NA
- COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL FAMILY: DYE/WATER/GLYCOL
HAZARDOUS COMPONENTS CAS # WEIGHT %
GLYCOL FL PROP 92 15-25%
No PEL established. See ingestion note.
PYRROLIDONE, 2- 616-45-5 5-15%
No PEL established.
PHTHALOCYANINE DYE FL PROP52 1-10%
0.5-2% copper in complex form.
OSHA 1.0 mg/m3 (as Cu dusts/mists).
See note under carcinogenicity.
ISOPROPYL ALCOHOL 67-63-0 1-10%
ACGIH TWA-TLV 400 ppm. TSCA Sec 12(b) export notification required.
The New Jersey Trade Secret Registration Number of proprietary
ingredients is controlled by the KIMBERLY-CLARK PRINTING TECHNOLOGY
product item number. Ingredients not precisely identified are
proprietary or non-hazardous. Values are not product specifications.
- HAZARDS IDENTIFICATION
HMIS CODES: H F R P
1 0 0 C
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: None reported
or known to exist for the product unless listed here:
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Eye/skin: May cause irritation.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: May cause
gastrointestinal irritation, vomiting, nausea, and diarrhea.
May be harmful or fatal if swallowed; may produce central nervous
system depression, kidney and liver damage.
ACUTE HEALTH HAZARDS: Moderate eye and skin irritation.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: None known
or determined for the product
CHRONIC HEALTH HAZARDS: None known or determined for the product.
CARCINOGENICITY: Product not tested. IARC, NTP, OSHA listed
carcinogen components equal to or greater than 0.1% by weight
will be listed in paragraph 2 and described as carcinogens,
if any.
- FIRST AID MEASURES
EMERGENCY AND FIRST AID PROCEDURES:
Swallowed: Do NOT induce vomiting. Call a doctor and contact
local poison control center immediately.
Eye contact: Flush eyes thoroughly with water. Seek medical
attention if irritation persists.
Skin contact: Wash contaminated areas with soap and water.
Inhaled: Remove victim to fresh air.
- FIRE FIGHTING MEASURES
FLASH POINT: N/A (Non-flammable water based)
METHOD USED: NA
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: NA UPPER: NA
EXTINGUISHING MEDIA: NA
SPECIAL FIREFIGHTING PROCEDURES: NA
UNUSUAL FIRE AND EXPLOSION HA ZARDS: NA
- ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Soak up on paper or other absorbent and scoop into closed containers.
Flush area with plenty of water.
- HANDLING AND STORAGE
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Storage temperature: Standard room temperature (68 degrees Fahrenheit).
Special sensitivity: Heat, light, moisture.
Precautions: Keep container closed. Store away from traffic.
OTHER PRECAUTIONS: None.
- EXPOSURE CONTROLS/PERSONAL PROTECTION
RESPIRATORY PROTECTION: Not necessary.
VENTILATION: Mechanical ventilation is acceptable.
PROTECTIVE GLOVES: Rubber
EYE PROTECTION: Goggles or safety glasses with side shields.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Impervious clothing
where skin contact is unavoidable; eyewash station.
WORK/HYGIENIC PRACTICES: Avoid contamination of food, drink,
etc. No smoking when handling.
- PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT: > 200¯ F SPECIFIC GRAVITY (H2O=1): >
1
VAPOR PRESSURE (mm of Hg): ND VAPOR DENSITY (AIR = 1): > 1
EVAPORATION RATE (BUTYL ACETATE=1): > 1 MATERIAL VOC: Not measured
PHYSICAL STATE: Liquid COLOR : CYAN
ODOR: Mild SOLUBILITY IN WATER: Complete
- REACTIVITY
STABILITY: Stable
CONDITIONS TO AVOID: None known
INCOMPATIBILITY (MATERIALS TO AVOID): Oxidizing materials and
strong
acids.
ITEM NUMBER: F497166 DATE PRINTED: 08/20/1999 Page: 3
HAZARDOUS DECOMPOSITION OR BYPRODUCTS: Oxides of carbon and nitrogen.
HAZARDOUS POLYMERIZATION: None
- TOXICOLOGICAL INFORMATION
No information available.
- ECOLOGICAL INFORMATION
No information available.
- DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD: Waste shall be disposed of in accordance
with federal, state, and local environmental control regulations.
- TRANSPORTATION INFORMATION
D.O.T. SHIPPING NAME: Not regulated.
- PRODUCT REGULATORY INFORMATION
OSHA STATUS: Product not tested. It is not considered to be
toxic per 29CFR1910.1200 but is considered to be a skin/eye
irritant.
USA TSCA STATUS: This product meets the requirements of the
Toxic Substances Control Act.
INTERNATIONAL EXPORT/IMPORT STATUS: Not determined for every
country.
Contact KIMBERLY-CLARK PRINTING TECHNOLOGY for certification
if required. Formulas are proprietary, so ingredient lists may
only be released to Customs/Health offices designated to control
trade secrets.
SARA TITLE III SECTION 313 TOXIC CHEMICALS: Product not listed.
SARA listed ingredients at or above De Minimis reporting levels
are noted in paragraph 2, if any.
RCRA HAZARDOUS WASTE NUMBER/STATUS: If discarded in its purchased
form, this product would not be a federal hazardous waste either
by listing or by characteristic. States, however, often have
stricter criteria. Users should check with their state regulatory
agencies for current hazardous waste criteria. Under RCRA it
is the responsibility of the product user to determine at the
time of disposal whether a material containing the product or
derived from the product should be classified as a hazardous
waste (40CFR261.20-24).
OZONE-DEPLETING CHEMICALS: No regulated ingredients.
NEW JERSEY
REPORTABLE COMPONENTS CAS #
WATER, DEIONIZED 7732-18-5
GLYCOL FL PROP 92
FILLER, NONHAZARDOUS SUPPLYPROP38
PYRROLIDONE, 2- 616-45-5
PHTHALOCYANINE DYE FL PROP52
The New Jersey Trade Secret Registration Number of proprietary
ingredients is controlled by the KIMBERLY-CLARK PRINTING TECHNOLOGY
product item number.
CALIFORNIA PROPOSITION 65 (CARCINOGENS):
REPORTABLE COMPONENTS CAS # WEIGHT %
. NONE UNLESS LISTED, AS FOLLOWS:
CALIFORNIA PROPOSITION 65 (REPRODUCTIVE TOXINS):
REPORTABLE COMPONENTS CAS # WEIGHT %
. NONE UNLESS LISTED, AS FOLLOWS:
- OTHER INFORMATION
All information appearing herein is based upon data obtained
from the manufacturer and/or recognized technical sources. This
information is believed to be correct, but does not purport
to be all inclusive and shall be used only as a guide. KIMBERLY-CLARK
PRINTING TECHNOLOGY, INC. makes no warranty, express or implied,
as to the accuracy or completeness of this information. It is
the user's responsibility to determine the suitability of this
information for the adoption of necessary safety precautions
and/or compliance with federal, state, and local laws and regulations.